Sterilised grainPremium CVA substrateMade for Australian growers
Aus Myco KingdomThe home of Australian mycology

Buying guides 5 min read

How our sterilised grain is made: a small-batch walk through, step by step

There is no secret to a good bag of grain, just ten steps done properly in batches small enough to check. Here is each one, and why it matters in your tub.

People ask how is sterilised grain made, usually after a bag from somewhere else has gone sour and they want to know what went wrong. The honest answer is that the sterilised grain process is simple, and every step of it is easy to rush. We make our bags in small batches, by hand, and this is the walk through: what we do at each step, why it matters, and what it means for the bag when it reaches your tub.

How is sterilised grain made? The short version

Clean grain is soaked and simmered until each kernel holds the right amount of water, dried on the surface, dosed with nutrients, bagged in a filter-patch bag with an injection port, sterilised at 121°C under pressure for a full cycle, cooled slowly, checked and shipped. Every one of those steps answers a specific failure, and the three failures that matter most are the wet spot, the surviving endospore and the slow bag. Keep those three in mind as you read.

Grain and water: selecting, rinsing, soaking

  1. Select and rinse the grain

    We start with clean, whole Australian grain, wheat, oats, corn or milo, and rinse it until the water runs clear. Dust, chaff and broken kernels are the first thing bacteria colonise, and a broken kernel leaks starch into the bag. Rinsing is boring, and skipping it is the first shortcut a production line takes.

  2. Soak

    The grain soaks in water, usually overnight, long enough for the kernels to take up water to the centre. A long soak also encourages the dormant endospores on the grain to germinate, and a germinated spore is far easier to kill in the autoclave than a dormant one.

Setting the moisture: simmer, drain, enhance

  1. Simmer to the right moisture

    The soaked grain is simmered, not boiled hard, until the kernels are plump and cooked through without splitting the skin. This is where hydration is set. Too short and the centre of each kernel stays dry and the mycelium stalls; too long and the skins burst, starch leaks out, and the bag is set up for a wet spot before it is even sealed.

  2. Drain and dry the surface

    The grain is drained and spread out until the surface of every kernel is dry to the touch, with no free water. This is the step that decides whether a bag gets a wet spot. Water inside the kernel feeds mycelium; water between the kernels feeds bacteria. We want the first and none of the second.

  3. Nutrient enhancement

    A measured nutrient boost is mixed through the grain so each kernel carries more than plain starch. Enhanced grain colonises faster and gives the mycelium more reserves to carry into the substrate. It also feeds contaminants, which is why this step only works when the sterilising step is done properly.

The autoclave: the full cycle at 121°C

  1. Bag by hand

    The grain is weighed into filter-patch bags, 1 kg or 2 kg, each with a 0.2 micron patch and a self-healing injection port, and sealed. Bagging by hand means each bag is filled to the same depth and the patch is kept clean and uncreased, which matters because a creased patch is a blocked patch.

  2. Load and run the full cycle

    The bags go into the autoclave in a shallow load with space between them, and the cycle runs at 121°C under pressure for the full time, long enough for the heat to reach the centre of the middle bag, which for grain is well over an hour and depends on the load. This is the step that kills endospores. A shorter cycle, a cooler cycle or a deeper load leaves survivors, and survivors show up as a sour, wet bag five days after you inoculate.

After the autoclave: cooling, checking, shipping

  1. Cool slowly

    The autoclave is left to come down to pressure and temperature on its own. Pulling bags out hot bursts kernels, drives steam out through the patch and sucks air back in as the bag cools. Slow cooling keeps the moisture where it belongs and the bag sealed.

  2. Check every bag

    Each bag is looked at by hand: patch intact, seal intact, no pooled water, kernels plump and separate, no split skins. A bag that fails does not go in a box. This check is the thing a small batch makes possible and a production line makes impossible.

  3. Pack and ship within days

    Bags are packed and sent tracked by Australia Post, standard or express, within days of the cycle. Grain loses moisture slowly through the patch, so a fresh bag is a better-hydrated bag. Nothing is made for a shelf.

Why small batches by hand beat a production line

None of these steps is secret. The difference is whether each one is done properly, and that comes down to batch size. A production line optimises for throughput: a shorter soak, a faster boil, a deeper autoclave load, a shorter cycle, stock on shelves to smooth out demand. Each of those is a small compromise, and together they add up to the bags that go sour. A small batch grain spawn run is slow by comparison, but every kernel is properly hydrated, every bag reaches temperature, and every bag is checked by a person before it ships. That is also why ours is fresh grain spawn when it lands anywhere in Australia, not something that has been sitting since autumn.

What it means in your tub

A bag made this way colonises evenly from the port outward, with no wet spot at the bottom and no stall halfway. On properly hydrated, enhanced grain, a bag of our sterilised grain is usually fully white in two to three weeks at 20 to 26°C, and it breaks up cleanly when you spawn to substrate. If you want to understand the bag itself, the patch, the port and how to inoculate through it, read sterilised grain bags explained.

Questions people ask

Why not just boil the grain?

Boiling reaches 100°C, and bacterial endospores on cereal grain survive that. They need 121°C under pressure for a full cycle. Boiled grain in a sealed bag goes sour within days of inoculation.

How long does the autoclave cycle take for grain?

Well over an hour at 121°C, depending on the load, plus the time to come up to pressure and cool down. We never shorten it to fit more batches in a day.

Can I make my own grain spawn bags at home?

You can, with a pressure cooker that reaches 15 psi, filter-patch bags and patience. Most of the failures people have are in hydration and cycle time, which is exactly the slow part we take off your hands.

How fresh is the grain when it arrives?

Days old. Bags are made in small batches and shipped within days of the cycle, tracked Australia-wide, so they arrive at full moisture rather than after months on a shelf.

Written by the Aus Myco Kingdom crew. Everything here is general growing information for gourmet and medicinal species; your room, your climate and your culture will have the final say.

Related guides

All guides

The drop list

Join the kingdom.

Restocks, new cultures and first dibs on grow kits. One email when something lands, nothing more.